moulding design
Published:2014-12-22 09:15:19    Text Size:【BIG】【MEDIUM】【SMALL

Low Cost Tooling Tool Design

Low Cost Tooling,Tool Design, moulding designAt Sofitel we have various tooling options available to you, offering different levels of capability from prototype through to short pre-production runs through to full production quantities.
We can provide you with:
Low volume :-Soft tooling for a few thousand cycles
Medium volume:-P20 (pre toughened) tooling for up to 20,000
Higher volume :- Fully hardened tooling in various guises up to 1,000,000 cycles maintenance free.

Where the cost of several mould tools would be prohibitive, we can offer Family tools that produce more than just one component design.

Mould Tooling,Mold Design
Single Cavity
(low volume/low cost)
Mould Tooling,Mold Design
Multi Cavity
(lower component cost)
Mould Tooling,Mold Design
Family Tool
(lower tooling cost)

All available in Soft or P20 or Fully Hardened tooling

  • Full experience of mould design, tool design and manufacture.
  • We can tackle the most complex automotive and security components to simple speaker components feet!
  • Some customers just tap into our expertise for tool design and undertake manufacture of tooling and components themselves!

plastic mold tooling design
3D Solid Model
plastic mold tooling design
Mastercam Model
plastic mold tooling design

Construction Injection Molds Classification

classification or types of mold injection very depend on what we need to make the plastic parts, because every parts have specific and unique design. when design molds we must see what the influencing factor like geometry, number of cavities, ejection principle, plastic material and shape of parts.

The basic classification of mold based on construction shown on picture below

1. Standard Molds

the standard mold is the most simple design, basically the standard molds is same as two plate molds construction, they divided in two side : cavity side and core side, cavity side is the side that construct to flowing plastic material from nozzle to cavity parts, basically they consist of sprue, runner.

Plastic Mold,2 plate moldcore side construct to make shape for core, demolding system and ejection system, at this side we design ejection system.
standard mold have one parting line, and have one opening direction. this type of mold use in all kinds of plastic parts that doesn't have undercut, inner and outer screw.
Light brown color little and straight in ejection system is shown ejector pin.

2. Slide mold

development from this mold type is the used slider parts in various molds types, basic slide mold is transfer horizontal movement of mold to vertical movement, this types of molds is used to make parts with undercut, you should see more at the post when we need slider for learn more.

Plastic Mold,slider mold3. Three plate molds
basically three plate molds has two parting line, and floating plate, floating plate support by support pin, Since the mold has two parting planes, the runner system can be located on one side of floating plate or make special plate that attach in floating plate, we called runner plate, see post about runner plate.Three plate molds are used because of their flexibility in gating location. this types of molds is flexible even use in multiple cavity.

Plastic Mold,3 platesnote : floating plate also called cavity plate or plate number 3, to know more the different between two plate mold and three plate mold see the posting about Basic and Types Molds Construction

4. Split Cavity Mold
basically the split cavity is same as 2 plate standard mold, but the cavity have split block to make undercut product or external threads.

Plastic Mold,Split Cavitythis type of mold use when the slider is not enough to make the undercut or the threads. the disadvantages of this mold is when use for little parts, the construction will difficult.

5. Mold With Screw Device
this mold special to make thread forming, the core can be rotate when demolding process, both internal or external threads can be forming by this type mold.

Mould Tooling,Mold Designfrom those picture we can see that they have gear device, the gear will rotate when form thread.
6. Stripper Ejector Moldthis type of mold have special purpose to make a cup shape without undercut, stripper ejector will make ejection more easy, same movement and power at the product and without a lot of marks in product

Mould Tooling,Mold Design
Molds with complex and difficult design can be integrated or combined one to the others mold type.

Mould Tooling,Mold DesignMoldflow Plastic Adviser, Plastics Insight, Moldflow Mpi, Mold flow communicator and Mold Adviser are Mould flow software products for simulating the injection molding of plastic materials. DSW use CAD Connectivity Tools to link structural CAD - CAE to MPI, MPA and MPX Community projects in the plastics and tool making industry.

After plastic design elements and cost elements have been considered, it's time to get the plastic molded. This step is done entirely on the part of production team. After all,DSW is not a consulting or design firm, but also a trouble shooter and analyses technician. The steps of the molded plastics production process are carefully planned and adhere to industry certification standards. In addition, customers get the benefit of experienced plastics engineers working on their component part. The plastic is cooled and packaged after molding.

Plastic Mold, Molding designMould Tooling,Mold DesignMould Tooling,Mold DesignMould Tooling,Mold DesignMould Tooling,Mold DesignMould Tooling,Mold Design

Products Search
Copyright(C)2009-2014  Yuyao XiangHao Mould Technology Company limited